10kw 400V 905~1400rpm Brush DC Electric Motor

10kw 400V 905~1400rpm Brush DC Electric Motor

 

Z4 Sequence DC Motor     

Electrical power: one.4kw – 600KW

Voltage: Regular 160V, 400V, 440V

Speed: Rated Velocity reference

Protection Diploma: IP21S

Insulation Class: F

Responsibility: S1

Bundle: Export Wooden Package

Payment: forty% in progress, balance by T/T or L/C at sight

 

Z4-132-2, 10KW, 400V, 905~1400r/min, IC06, IP21S, F Insulation

CZPT Info

 

Mounting Dimensions

CZPT

1. Mounting and Type of building

Mounting modes comply with the Condition CZPT GB/T997 stipulated as follows:

2. Safety and Cooling Technique.

The standard cooling approach of motor is IC06, It implies it have a blower for ventilate, also it can be created for IC17, It means use pipe as the cold air inlet, the air outlet is shutter composition. Also it can be created for IC37, it means the cold air’s inlet and outlet the two use pipe. And it’s have numerous deriving kind, this sort of as self-air flow, axial movement fan type, enclosed variety, air-air cooler type, etc. The request for the air movement, blast stress, power of the air blower, and so forth of different frame motor remember to see technological knowledge sheet one. The safety degree of total collection Z4 motor reaches IP21S

a. For Z4-100 – Z4-a hundred and sixty, The blower is mounted on the non-travel side.

b. For Z4-a hundred and eighty – Z4-450, The blower is mounted on the push facet.

c. The required cooling air volume, air force and admirer motor potential are shown under:(Table 1)

*All the ventilating supporter motors are a few section, two pole, 380V.

Motors with the following five strategies of cooling can also be requested, but prior consultations are required.

a. Frame measurement 100 up to 250 might be manufactured into the totally enclosed, body cooled motor(IC410).

b. Frame dimension one hundred eighty up to 250 could be made into the separately ventilated motor with blower mounted on its non-travel facet(IC05).

c. Frame dimensions 100 up to 200 could be manufactured into self-cooled open up motor with its personal admirer mounted on the shaft(IC01).

d. Body dimension a hundred and sixty up to 355 may be manufactured into entirely enclosed motor with inside cooling air circulation by independent air-air warmth exchanger mounted on it(IC666).

e. Frame dimensions a hundred and sixty up to 450 may be manufactured into completely enclosed motor with unbiased air-h2o heat exchanger mounted on it(IC86W).

 

From the travel end(Non-commutator placement), The common terminal box is on the appropriate place of the motor frame. For the request by client, the terminal box can be created on the reverse placement. Also the shaft can be manufactured as double shaft finish. The rotor shaft’s rotation course is counter clock-clever seen from the situation of commutator. The driving manner is adaptable coupling connection, also can be use for the driving method have certain radial force(this sort of as belt drive or gear drive), It is allowable radial power need to not exceed the price of graph.(see attached B)

 

three. Add-ons for electric powered motor

In accordance to customer’s ask for, the motor can be designed to allocate for tacho generator, pulse generator, centrifugal switch, arrester brake and so on.

Observe: the specification, energy and weak-magnet pace assortment is only for reference, For the refresh of new systems, new resources, the knowledge of the catalog will be transformed appropriately.

 

CZPTal performance

1, complex info must be employed in accordance to the pursuing info function conditions                  

A. altitude does not exceed 1000m,
B. bordering air temperature is not a lot more than forty ° c,
C. perform environment need to not have acid and alkaline or other to touch with insulation   effect of fuel.
D. motor for steady responsibility (S1),
E. motor armature loop and excitation circuitry by static electric power, rectifying energy source by dc generators.

F. the sequence motor functionality with GB/T755 the basic engineering of motor.
2, motor 160V rated voltage is common, 440V. In accordance to the particular conditions can derive   220V and 400V or other voltage.
three, motor rated speed 3,000, fifteen, ten, 750, 6, five, 4, 3, 200r/min of 9.
To minimize the armature voltage constant torque management, decrease excitation constant power voltage for pace. Velocity assortment of technological information desk saw.

In the pursuing with rated voltage regulating pace is consistent torque. It is no significantly less than the bare minimum speed regulation 20r/min, still can maintain the rated velocity, torque.

four, Separate excitation is the simple excitation kind of the motors. Nominal area voltage: 180V. Other excitation voltages are also acceptable on request. 
Pressured excitation is permitted with the voltage of much less than 500v. When a motor is generally working, its excitation existing should not be increased than the rated excitation existing.

To make certain the dependability of the insulation of excitation method, disconnect excitation circuitry on a field winding resistance, release ends in parallel to avert self-induction potential. In its worth common excitation voltage is about 7 occasions the subject winding resistance (chilly state). Whilst the field voltage is larger than nominal voltage, the benefit of shunt resistance may possibly be decrease than seven times field resistance, normally larger than seven occasions.
five, For frame dimension Z4-315, Z4-355,Z4-four hundred, and Z4-450, compensating windings are provided. For body dimensions Z4-250 and Z4-280, the motors are feasible with a compensating winding also.

6, A marked earthing terminal is offered for the motors.

seven, The efficiency listed in the info sheet are for rated output, voltage and velocity , and incorporate excitation losses, excluding that of different ventilating followers.  

Get Observe

one. Pls examine our goods catalog and verify the motor variety and specification before location get,  and variety variety as attainable as common technical specs proven in catalog. For motor  body dimensions, electricity, voltage, speed, thrilling method, interesting voltage and mounting type, ought to be pointed out clear in sales agreement. This sort of as Z4-one hundred eighty-31, 37KW, 440V, 1000r/min, divided excitation 180v, horizontal mounting with toes or IMB3.

two. Some unique requirements this kind of as : double shaft conclude, terminal box situation are mounting in the reverse way, counter clock-smart rotation need to be mentioned plainly in the agreement.

3. If the customer need variety, specification are not record in the catolog, or for other special requirement,  the deal or the pre-production arrangement need to be signed after equally party’s discussion and arrangement

four. All the motors , Other than the shaft extension key, all the components are not in the extent of source, If the equipment or spare components are requested,  these kinds of as the brush, brush holder, and many others,  pls notice the title, specification and quantities of the components in the deal.

five. For particular environment working issue, motor would be used in humid and sizzling regions,  pls label TH in the origin sort.

Packaging & Delivery

Screening Equipment

10kw 400V 905~1400rpm Brush DC Electric Motor